Content
- 1 What an Extrusion Screw Actually Controls
- 2 Extrusion Screw Geometry: A Quick Working Reference
- 3 Choosing an Extrusion Screw by Cable Material
- 4 What Steel an Extrusion Screw Is Made From
- 5 Wear Mechanisms and Realistic Service Life
- 6 When an Extrusion Screw Is Finished
- 7 Matching the Screw to the Whole Line
- 8 Acceptance Tests Before You Accept Delivery
- 9 Frequently Asked Questions About Extrusion Screws
A cable plant running 1.20 mm PVC building wire at 70 m/min called in a technician because the diameter was drifting plus or minus 0.04 mm and every fifth drum showed a faint sharkskin band. The operator had already adjusted all four barrel temperatures twice and changed the haul-off speed. Nothing moved the needle. When the screw was pulled and measured, the metering section flight depth had worn from 6.10 mm to 5.95 mm over four years of three-shift operation.
That is the whole lesson of the extrusion screw in one story. Before you touch a temperature controller, verify three things about the screw: its geometry, its material grade, and its current wear state. Everything else — output rate, melt temperature, pressure stability, surface finish, concentricity — follows from those three.
What an Extrusion Screw Actually Controls
An extrusion screw is the only component inside the barrel that simultaneously governs conveying, melting, mixing and pressure build-up. In wire and cable work that translates into four measurable outputs:
- Output rate. Screw diameter, flight depth and speed set how many kilograms per hour reach the crosshead. On a 45 mm screw running 60 rpm with PVC, that is typically 60 to 90 kg/h.
- Melt temperature uniformity. A screw with poor mixing leaves the melt 8 to 12 °C hotter near the barrel wall than at the core, and that gradient shows up as ovality.
- Pressure stability in the metering zone. Diameter tolerance of plus or minus 0.02 mm lives or dies here. Pressure pulsation of 2 bar is enough to produce visible diameter ripple.
- Dispersion quality. Color masterbatch streaks, unmelted gel particles and cloudy insulation are screw problems far more often than they are material problems.
The practical consequence is that a screw is not a generic spare part. Two machines with identical barrel diameters and identical drive power will produce completely different wire if one screw was designed for soft PVC and the other for cross-linked polyethylene. If you are still mapping the machine layout, the guide on which parts an extrusion machine is composed of is a useful starting point before you look at screw design in isolation.
Extrusion Screw Geometry: A Quick Working Reference
Purchasing a replacement screw without a drawing is the single most common mistake in this category. Five numbers matter, and they interact. The table below summarizes the ranges that are routinely used for wire and cable insulation and sheathing.
| Parameter | Typical Range | What It Governs | Fault When Out of Range |
|---|---|---|---|
| L/D ratio | 20:1 to 25:1 for PVC; 25:1 to 30:1 for polyolefins | Available length for melting and mixing | Below 20:1, unmelted particles and rough surfaces |
| Compression ratio | 2.5:1 to 4:1 solid insulation; 1.5:1 to 2.0:1 foamed | Shear heat generated and air removal | Above 4:1, scorch and core-side burning |
| Flight pitch | 0.8D to 1.2D | Conveying efficiency per revolution | Short pitch cuts output without improving quality |
| Metering flight depth | 0.05D to 0.12D | Pressure stability and diameter tolerance | Too deep, ripple; too shallow, shear overheating |
| Screw-to-barrel clearance | 0.002D to 0.005D | Leakage flow over the flight land | Worn clearance means lost output and longer residence time |
One relationship is worth stating plainly because it causes the most arguments on the shop floor: a higher compression ratio does not automatically mean better melting. It means more shear heat. On thin-wall insulation over a 0.50 mm conductor, excess shear heat travels through the copper and burns the insulation from the inside, which is exactly the defect that appears as a brown core-side ring in a cross-section.
A second relationship concerns flight depth against screw speed. A deep-flighted screw running at high rpm produces output without much temperature rise, but it also produces a weaker pressure signature. A shallow-flighted screw gives you a very stable diameter on a small conductor, then hits 250 °C melt temperature when you try to raise the rate. Selection is always a trade-off, and the trade-off is decided by the conductor size and the wall thickness you run most often.
Choosing an Extrusion Screw by Cable Material
Material family drives screw selection more than machine size does. Four groups cover the majority of cable production.
PVC and PE Solid Insulation
A general-purpose single-flight, gradually compressing screw with an L/D of 20:1 to 25:1 handles plasticized PVC and polyethylene without difficulty. These compounds are thermally forgiving, so a three-zone screw with a straightforward 3:1 compression ratio is enough. Add a short Maddock or pin mixing section if you run colored compounds and see streaks.
LSZH, XLPE, TPE and TPU
Low-smoke zero-halogen compounds are heavily filled, often with 55 to 65 percent by weight of aluminium hydroxide or magnesium hydroxide. The filler is abrasive and it raises viscosity, so the screw needs a barrier or dispersive mixing zone, a slightly deeper metering section to relieve shear, and a hardened surface. Cross-linked polyethylene behaves differently again: because cross-linking is triggered downstream, the screw must deliver the melt without letting temperature run away, which usually argues for an L/D of 25:1 to 28:1 with a moderate compression ratio in the 2.8:1 to 3.2:1 band.
LSZH/XLPE/TPE/TPU Core Wire Insulation Extrusion LineLSZH/XLPE/TPE/TPU Core Wire Insulation Extrusion Line is an non-standardized equipment with customization. The main machine model is generally 30-65mm. It is suitable ...View Product →
FEP and PFA High-Temperature Compounds
Fluoropolymers process between 360 °C and 400 °C and release aggressive decomposition products if the melt sits too long. Screws for these materials run a low compression ratio, sometimes as low as 2.0:1, with a short compression zone and generous flight clearance to limit dead zones. Everything upstream of the screw matters too, which is why the insulation extrusion machine range for these materials is normally specified as a matched screw-and-barrel set rather than a screw alone.
Chemically Foamed PE and PP
Foamed insulation for coaxial and CATV cable needs a screw that seals the melt so that the blowing agent decomposes under controlled pressure. Compression ratios of 1.5:1 to 2.0:1 with a long metering zone are standard, and any wear that opens the flight clearance ruins the cell structure immediately. Foam cells you can see with the naked eye on a stripped conductor usually mean the screw is finished.
What Steel an Extrusion Screw Is Made From
Screw grade is chosen against the compound, not against the price list. Five grades cover almost all cable work.
- Nitrided steel (38CrMoAlA). A nitrided case of 0.4 to 0.7 mm with surface hardness around 900 to 1100 HV. This is the default for PVC, PE and general polyolefin work. It is cost-effective and adequate until fillers enter the picture.
- Bimetallic (centrifugally cast high-chromium alloy). Selected when the compound contains abrasive fillers such as ATH, MDH or glass fibre. Wear resistance improves several-fold over nitrided steel on LSZH grades.
- Powder metallurgy high-speed steel. Uniform carbide distribution gives excellent wear resistance with better toughness than fully cast alloys. Used where both abrasion and impact are present.
- Nickel-based or cobalt-based hardfacing. Applied as a welded overlay on the flight lands. This is the usual answer for fluoropolymers and other corrosive melts, where the base alloy would be attacked long before it wore out.
- Chrome-plated or PTFE-coated screws. Occasionally used for short runs of transparent compounds where sticking is the problem. The coating is a wear item and should not be treated as a permanent upgrade.
Whichever grade you buy, the screw and the barrel are a wear pair. Fitting a bimetallic screw into a nitrided barrel accelerates barrel wear instead of reducing total cost, because the harder surface simply moves the wear to the softer partner.
Wear Mechanisms and Realistic Service Life
Three wear mechanisms act on an extrusion screw, and they progress at very different rates.
- Abrasive wear. Driven by filler content and filler hardness. It shows up first on the flight land, then spreads into the flight flank and the metering section.
- Corrosive wear. Fluoropolymer melts that decompose release hydrogen fluoride, which attacks steel even at moderate temperatures. This mechanism removes material from the whole screw surface rather than from a single contact area.
- Adhesive wear and erosion. Gradual, and largely a function of running hours and start-up discipline. Dry starting a machine that has been sitting cold for a week is a reliable way to shorten screw life.
As a planning figure, a nitrided screw processing unfilled PVC on three shifts typically holds its geometry for three to five years. The same screw running a filled LSZH compound at high output may need replacement or reconditioning in 12 to 24 months. Fluoropolymer screws last longer in calendar terms but often fail from corrosion pitting rather than from dimensional loss.
This is where the material decision becomes a cost decision. A cheaper nitrided screw that lasts 14 months on a filled compound costs more per production hour than a bimetallic screw that lasts four years, even at twice the purchase price.
FEP/PFA/ETFE/PEEK/PA High Temperature Core Wire Insulation Extrusion LineFEP/PFA/ETFE/PEEK/PA High-Temperature Core Wire Insulation Extrusion Line is a non-standardized equipment with customization. The main model is generally 20-50mm. It i...View Product →When an Extrusion Screw Is Finished
Replacement decisions get easier when you replace opinion with measurement. Pull the screw, clean it properly, and check these five points against the original drawing.
- Metering flight depth has lost more than 15 percent. At that point output and pressure stability both fall measurably.
- Flight land width has grown and the land edges are rounded. A rounded land wipes poorly and lets leakage flow rise.
- Clearance between screw and barrel exceeds roughly 0.005D. Check the barrel bore at the same time; a worn barrel will not save a new screw.
- Visible corrosion pits, gouges or spalling on the flight surfaces. These trap material and create black specks that no amount of purging removes.
- The same product settings now require a barrel temperature 10 °C higher than two years ago to achieve the same surface finish.
Before scrapping, ask whether reconditioning is viable. Hardfacing and regrinding of the flights can restore geometry at perhaps 40 to 60 percent of new-screw cost, provided the base material has no deep corrosion damage and the screw is long enough to allow material removal. Keep the measurement record; a screw life history is one of the most useful maintenance documents a cable plant can hold.
Matching the Screw to the Whole Line
A screw never works alone. Four interfaces determine whether a correctly designed screw actually performs on your floor.
Drive and speed range. A screw designed for 30 to 120 rpm will not deliver its rated melt quality if the drive is fixed at 200 rpm. Insulation lines typically operate between 40 and 90 rpm for control, while sheathing lines for large cables often run slower with a deeper flight.
Crosshead and tooling. A low-compression screw paired with a high-pressure crosshead produces unstable flow. The screw's pressure generation and the head's pressure consumption must be in balance, or the melt will fluctuate regardless of how the screw is built.
Haul-off and tension control. Diameter ripple is often blamed on the screw when the real cause is a haul-off that hunts under changing capstan friction. It is worth verifying downstream stability before ordering a new screw.
Barrel heating zones. A screw with a short compression zone needs a barrel that can hold a tight temperature profile across three or four zones. A two-zone barrel turns a good screw into an average one.
Sheathing is a useful illustration. A jacket extruder is usually chosen to run at a lower melt temperature and a higher throughput than an insulation extruder, because the jacket thickness and the required surface finish are both more forgiving. That combination calls for a deeper metering section and a longer feed zone, which is a different screw from the one in your insulation line even when the barrel bore is identical.
PVC/PE/PP/PU Sheath Extrusion LinePVC/PE/PP/PU Sheath Extrusion machine is a non-standardized equipment with customization. The main machine model is generally 70-150mm, which is commonly used in wire ...View Product →Acceptance Tests Before You Accept Delivery
Whether a screw arrives as a spare or as part of a new machine, run these checks before the supplier leaves site.
- Measure flight depth at six points along the metering section and compare against the drawing. Tolerances of plus or minus 0.02 mm are realistic.
- Check straightness along the full length and surface finish on the flight lands. Hand-polished lands should show no circumferential chatter marks.
- Verify hardness on the flight land, not on the shank. A nitrided screw should show a consistent case reading along the whole working length.
- Fit into the barrel and confirm clearance with a feeler gauge at three positions. If the screw binds at operating temperature, the problem will appear at running temperature, not at room temperature.
- Run a production trial on your own compound and record output, melt temperature and diameter variation over at least 30 minutes. This baseline is what you will compare against in two years.
Gemwell has been building cable extrusion machinery since 2005 and now supplies equipment to cable manufacturers in more than 40 countries. In 2024 the company separated its extrusion project into a dedicated branch in Dongtai, Jiangsu, with a CNY 10 million investment focused on extrusion equipment for electronic information transmission cables, and it holds eight invention patents and more than 30 utility model patents in the wire and cable equipment field. That background matters less than the measurement discipline described above, but it does mean spare screws and matched screw-and-barrel sets are available for machines already in the field.
Frequently Asked Questions About Extrusion Screws
How many extrusion screws does one machine need?
One working screw per extruder, but most cable plants keep a matched spare. If you run both PVC insulation and a filled LSZH compound on the same machine, a single spare screw will never be ideal for both, and two dedicated screws usually pay for themselves over three years of production.
How long does an extrusion screw last?
Unfilled PVC on three shifts typically gives three to five years before geometry loss becomes measurable in the product. Filled halogen-free compounds can cut that to 12 to 24 months. Fluoropolymer screws commonly fail from corrosion rather than abrasion.
Can a screw and barrel be replaced separately?
They can, but it is rarely wise. The clearance between them is the parameter that matters, and a new screw in a worn barrel can leave a clearance of 0.30 mm or more. Measure the barrel bore first; if it is out of tolerance, replace the pair.
Why is my extruder surging?
Surging is nearly always a feed-zone or metering-zone problem. Check the feed throat temperature first, then the flight depth in the metering section. A worn metering section cannot hold pressure, and the melt will pulse into the crosshead in waves.
Can an extrusion screw be repaired rather than replaced?
Flight hardfacing and regrinding are standard practice and can restore geometry for roughly 40 to 60 percent of the cost of a new screw. Repair is not viable when corrosion has penetrated the base material or when so much material has been removed that the flight depth specification cannot be reached.
Does compression ratio matter for thin-wall insulation?
It matters more than for thick jackets. Thin walls conduct heat away slowly and the conductor absorbs it quickly, so shear heat from an over-compressed screw reaches the copper and burns the inner surface. A ratio near 2.5:1 is generally safer than 4:1 on small conductors.
An extrusion screw is the least glamorous purchase in a cable plant and the one that shows up fastest in your scrap rate. The sequence that works is consistent: define the compound and the wall thickness, fix the geometry against those two facts, pick the steel grade against the filler and corrosion load, then measure the screw every year so that replacement is a scheduled decision instead of an emergency.
That maintenance record — flight depth at six points, taken annually and kept with the machine file — is the single cheapest tool available for holding diameter tolerance and surface quality steady across a screw's whole working life.
E-mail: info@gem-cablesolution.com
Address: No.8 Yuefeng Rd, High Tech Zone, Dongtai, Jiangsu, China | No.109 Qilin East Rd, Daning, Humen, Dongguan, Guangdong, China.
English
English
русский
日本語
Español
عربى
中文简体
Related Products


